Evaluation of the level of hardening of aluminum alloy chips intended for subsequent pressure treatment : научное издание | Научно-инновационный портал СФУ

Evaluation of the level of hardening of aluminum alloy chips intended for subsequent pressure treatment : научное издание

Тип публикации: статья из журнала

Год издания: 2021

Идентификатор DOI: 10.17212/1994-6309-2021-23.1-45-55

Ключевые слова: technogenic formations, chip processing, aluminum alloy, finite element method, plastic deformation

Аннотация: Introduction. It is noted that the chip is an undesirable type of metal scrap, because it has a developed surface, which creates conditions for more intense interaction with the surrounding atmosphere. This creates conditions for oxidation and gas saturat Introduction. It is noted that the chip is an undesirable type of metal scrap, because it has a developed surface, which creates conditions for more intense interaction with the surrounding atmosphere. This creates conditions for oxidation and gas saturation, especially at elevated temperatures typical of remelting processes. Therefore, the process of chip utilizing is considered, bypassing the remelting stage. The aim of the work is to establish the level of work hardening of chips during the processing of aluminum alloys and to predict its effect on the subsequent processing process. Research methods: to assess the deformed state, the finite element method was applied, implemented in the RAPID-2D software package. The sequence of actions included the creation of the initial shape of the deformation region and the configuration of the tool. The mutual displacement of the tool and the deformable material is specified using the corresponding boundary conditions. The deformable medium is a viscous-plastic material with power-law hardening, the physical and mechanical properties correspond to an aluminum-magnesium alloy. Results and discussion: the solution obtained shows that the degree of shear deformation in the chips can reach a value of more than 2. In this case, a higher level of deformation is localized on the side of the convex part of the chip. The comparison of the solution with those obtained earlier by other authors is carried out and its similarity is shown. In the considered solution, the difference in the degree of work-hardening of the chips along its thickness is 36 %. A variant of the sequence of processing the workpiece first by cold deformation, and then by cutting is considered. The field of application of the results of the work is the development of methods for the processing of technogenic formations. Conclusions. During the cutting process, the plastic deformation of the chips reaches significant values. In this paper, the difference in the degree of shear deformation in the chip thickness is established, depending on the proximity of the cut layer to the surface of the cutting tool. It is proposed to take this difference into account at the subsequent stages of chip processing. The presence of the marked inhomogeneity of mechanical properties leads to consequences in the form of an inhomogeneous distribution of the temperature of the beginning of recrystallization during subsequent operations of heat treatment or hot deformation treatment. The principle of additivity of the degree of deformation obtained by the metal at the stage of plastic shaping of the workpiece and the shaping of the chip itself is introduced.

Ссылки на полный текст

Издание

Журнал: OBRABOTKA METALLOV-METAL WORKING AND MATERIAL SCIENCE

Выпуск журнала: Vol. 23, Is. 1

Номера страниц: 45-55

ISSN журнала: 19946309

Место издания: NOVOSIBIRSK

Издатель: NOVOSIBIRSK STATE TECH UNIV

Авторы

  • Loginov Yuri (Ural Fed Univ, 19 Mira Str, Ekaterinburg 620002, Russia; Russian Acad Sci, Ural Branch, MN Mikheev Inst Met Phys, 18 S Kovalevskaya Str, Ekaterinburg 620137, Russia)
  • Zagirov Nickolay (Siberian Fed Univ, 79 Svobodny Ave, Krasnoyarsk 660041, Russia)
  • Ivanov Evgeniy (Siberian Fed Univ, 79 Svobodny Ave, Krasnoyarsk 660041, Russia)

Вхождение в базы данных

Информация о публикациях загружается с сайта службы поддержки публикационной активности СФУ. Сообщите, если заметили неточности.

Вы можете отметить интересные фрагменты текста, которые будут доступны по уникальной ссылке в адресной строке браузера.